LINER REPLACEMENT •
Pool Liner Replacement in
Empire Pools installs premium vinyl liners for pools — precision measuring, sub-base touch-ups, bead-track inspection,
and wrinkle-free vac set. We plan each replacement around South Shore wind and debris patterns off corridors like Merrick Road (NY-27A),
Sunrise Highway (NY-27), Merrick Avenue, Babylon Turnpike, and approach routes near the Meadowbrook State Parkway
so staging stays clean during set and fill. Our techs document measurements, track condition, and cut-ins so your new liner fits tight and opens crystal clear.
Every liner job starts with detail work that most companies rush: we verify wall height, radiuses, hopper/deep-end geometry,
and step/bench dimensions so the factory build matches your pool—not a “close enough” template. Before the liner goes in, we inspect the bead receiver,
coping, and track for brittleness or gaps that can cause the liner to pop out later, and we flag anything that should be corrected while the pool is empty.
On install day we prep the floor so it’s smooth underfoot (patching divots and low spots, addressing vermiculite or base wear where needed),
then we use a controlled vac set and staged fill pace to pull the liner evenly into corners and seams.
If conditions change—wind picks up, leaves start dropping, or access is tight—we adjust our staging (hose routes, equipment placement, debris control)
so the liner stays clean during the most important part of the job: the first few inches of water and final alignment before cut-ins.
• Local Insight
Tuned for South Shore breezes & busy road corridors
Homes closer to open bay air and high-traffic corridors can see quick breeze shifts that affect vac-set and seam alignment.
We stage equipment and manage fill pace so the liner sets smooth.
From neighborhoods near the Merrick LIRR Station to properties by Norman J. Levy Park & Preserve and the Merrick Golf Course,
we plan delivery, access, and hose routes to protect landscaping and speed the install.
What’s Included
- On-site measure (length/width/depths), wall height, and corner radii verification.
- Bead track inspection; replace brittle lock-in as needed (quoted on site).
- Sub-base touch-ups: floor trowel/patch, divot and wrinkle prevention.
- Liner hang and dual vac set for tight fit prior to filling.
- Cut-ins after water passes threshold: main drains, returns, lights, and skimmer.
- Hardware refresh (gaskets/faceplates/screws) as required by condition.
- Haul-away of old liner (available; quoted by weight/condition).
- Fill guidance to protect seams and prevent liner float; chemistry start-up.
- Note: Structural repairs, wall foam, vermiculite/base rebuild, and plumbing repairs are quoted if observed.
Why Choose Empire Pools
- expertise — manage wind, access, and fast weather swings during vac set.
- Wrinkle-free process with staged fill, seam alignment, and photo documentation.
- Transparent options: pattern choices, wall foam, step gaskets, and hardware refresh.
- Coordination for water delivery or hydrant permits when required (town rules vary).
- Clear scope & pricing before we begin — no surprises.
- Post-install check-in to confirm fit, fill progress, and chemistry balance.
Starting at $2,800 + tax
Local Reviews
★★★★★
“We’re right off Merrick Road and wanted a tight, clean fit. The liner is perfectly set and the corners are smooth.” — K. B.,
★★★★★
“They found a couple weak spots in the bead track during prep and fixed them before hanging the liner. That’s the kind of detail we wanted.” — M. R.,
★★★★★
“Great communication from measurement through install day. Cut-ins were clean and the vac set stayed wrinkle-free.” — T. S.,
★★★★★
“Our floor had a few low spots and they corrected them while the pool was empty. The base feels smooth and brand new.” — J. P.,
★★★★★
“Professional, organized, and on time. No wrinkles, no loose seams, and they walked us through the fill pace.” — R. D.,
Liner Replacement — FAQs
Do you replace pool liners throughout , NY?
Yes — we cover and nearby Nassau/South Shore areas. We typically schedule measurement first, then coordinate manufacturing and install timing.
What’s the process for a liner replacement (measurement to install)?
We measure your pool accurately (including steps/benches and deep-end geometry), confirm track/coping condition, and help you choose a pattern.
Once the liner arrives, we prep the base, hang the liner, vac-set, and then perform cut-ins after the water reaches the correct level.
How long does a liner replacement usually take in ?
Once the liner is on site, most installs are completed in a day. Fill time depends on water source and flow.
We’ll guide the fill pace to protect seams and reduce the risk of liner float.
Can you fix bead-track or coping issues while the pool is empty?
Yes. We inspect the bead receiver/track during measurement and again on install day.
If anything is brittle, cracked, or loose, we quote the fix before proceeding so the liner seats correctly long-term.
What can increase cost beyond the starting price?
Common add-ons are base repairs (vermiculite rebuild/patching), wall foam, hardware packages (gaskets/faceplates), track repairs,
and any structural or plumbing issues discovered once the old liner is removed. We’ll explain options and pricing before work begins.
What helps you quote faster for a liner replacement?
A few photos (wide pool shot + equipment pad + bead track close-up), your pool shape, approximate dimensions, wall height,
and any step/bench/deep-end details help us price accurately and avoid surprises.